The product provides an 'inert coating' which means it does not promote the growth of mold or mildew. Additionally, Drylok Extreme consists of an additive called 'mildewcide' which acts to further prevent the potential for mold or mildew to grow under paint.
The chemical makeup of Drylok paint is a particular food source that mold actually likes (mold also grows on wood and many other similar surfaces as those are food sources as well) so the mold has food in plenty if Drylok is present.
Recommended for the most demanding conditions and capable of resisting the hydrostatic pressure equivalent to a 33-foot-tall wall of water, DRYLOK Extreme does what other, broadly similar products do, only better.
Is specially formulated to resist mildew growth, is protected with ISPC leanguard™ biocide, has a breathable film, and stops 15 psi (greater than a wall of water 33 feet high).
Mold can grow down in the holes of cinder blocks. Molds can grow in many areas such as kitchen ceilings, underneath bathroom sinks and on carpet. However, many molds grow in areas much more difficult to see.
Though many people assume that a new coat of paint will solve mildew and mold problems, it won't. That's because paint cannot kill mold spores or prevent them from spreading.
Water that leaks in from your roof or pipes are the number one causes of mold in basement areas. A leak brings an endless supply of water and moisture to dark areas in your home. Since most pipes and roofs have a layer of drywall and insulation around them, they make perfect places for mold to grow.
per gallon of coverage, Sani-Tred can waterproof larger surfaces using less material and lowering your costs. Not only does Sani-Tred actually waterproof your basement, it has better coverage for less money in the long run. Drylok appears to be the more economical choice.
DRYLOK® Extreme Masonry Waterproofer is a product that you can use to help reduce moisture from your foundation walls from making your basement into a humid jungle atmosphere.
Just as with a thorough paint job, proper application of DRYLOK Masonry Waterproofer requires two coats. Dry times vary based on temperature and humidity, but it typically takes at least four hours for the product to dry.
Drylok is an indoor waterproofing paint, and while that has been mentioned several times, it is a crucial detail. Waterproofing your basement from the inside may be cheap, but it is by far the least effective way of waterproofing your basement, and this is because it never stops the source of the water.
NO, drylock will not do anything as to keeping water from coming through a crack, hole or any direct opening that is or may arise on the outside of your home in future....it is impossible for any paint to stop water from entering through a wall or from water entering through windows, tuckpointing needs etc.
This material is combustible, but will not ignite readily. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Toxic to aquatic life with long lasting effects (GHS category 2: aquatic toxicity - acute and/or chronic).
DRYLOK Masonry Waterproofer can be used over paint. In addition to using DRYLOK over any other cementitious waterproofing-type paint in good, repaintable condition, it can also be used over oil or latex-based paints on the inside of buildings.
The best way to reduce high humidity and condensation in basements is to deep-seal your concrete against moisture. Sealing the basement slab (and below grade walls) against water vapor transmission and possible water seepage is the key to preventing molds and mildew.
You should not paint your walls with Drylok or waterproofing paint, even if it is Drylok. You should not attach insulation directly to the walls of the foundation.
Cost to DRYLOK a Basement
The cost of using DRYLOK to seal a basement averages $0.60 to $1 a square foot. DRYLOK is a basement sealant material. It is a type of waterproof paint you can roll on yourself.
DRY TIME: To touch: 30 minutes • To recoat: 3 hours • Top coat with latex paint: 24 hours Note: Maximum cure and dry time will be prolonged when slightly humid and damp, cool conditions prevail.
When sealing basement floors and foundation walls the best concrete sealers to use are the Lithi-Tek 4500 primer followed by the Siloxa-Tek 8510 waterproofing sealer. If you are going to be installing flooring in the basement, it is best to use a moisture vapor barrier coating like the Vapor-Tek 440.
Oil Base DRYLOK® Masonry Waterproofer
Formulated for waterproofing all interior, exterior, above or below grade masonry walls, cinder and concrete blocks, stucco and brick, retaining walls, fish ponds, birdbaths, basement walls and foundations.
Apply a masonry waterproofing product to the walls
Seal/coat the interior of the walls with a suitable masonry waterproof product. When the paint dries, the sealant forms a watertight bond to stop water from seeping through. This is how you can waterproof your basement walls from inside.
Reduce Mold and Mildew
A dehumidifier is designed to reduce the moisture level in the air by extracting the excess water. By doing so, dehumidifiers can help prevent the growth of mold and mildew and improves the indoor air quality of your space.
Basement Humidity in the Summer
That air can make its way into your basement, increasing your humidity levels to around 60 percent. Because of this, homeowners must work to adjust those levels back to the ideal humidity level between 30 and 50 percent or risk mold, mildew and bacteria buildup.